Top Innovations Iron SF 475 User Manual

MODEL SF-475  
Fabric Steamer  
by Top Innovations, Inc.  
Please read all instructions before use.  
Mail in your warranty registration card.  
 
IMPORTANT SAFEGUARDS  
WARNING: To reduce the risk of fire, electrical shock, or injury,  
the following basic safety precautions should always be followed  
when using an electrical appliance.  
READ ALL INSTRUCTIONS BEFORE USING YOUR FABRIC STEAMER  
1. Unit Water Reservoir is designed to hold a maximum of 48 oz. (1420 ml.) of  
water. Use caution when filling, to avoid burns from spilling water, or possible  
electrical shock.  
2. DO NOT leave your SF-475 Fabric Steamer unattended when plugged in or not  
in use. Use only for its intended purpose as indicated in this manual.  
3.  
This unit is not a toy. Close supervision is required when using unit  
near children, pets, and plants. Steam produced by unit is hot and  
pressurized. Care must be taken to avoid burns or other injuries. Never  
point nozzle at people or pets.  
4. To reduce the risk of contact with hot water emitting from steam vents, hold  
appliance away from body and check for signs of condensation or leakage.  
5. DO NOT use this unit if electrical cord or outlet is damaged. DO NOT use unit if  
it is not working properly or has been dropped, damaged or left outdoors. If such  
damage occurs, DO NOT disassemble or attempt repairs, take unit to a qualified  
service person for examination and repair. Incorrect reassembly or repair could  
cause a risk of fire, electrical shock, or injury to persons when steamer is used.  
6. To reduce risk of electrical shock, DO NOT immerse in water or other liquids.  
DO NOT use electrical cord or Hose as a handle. DO NOT allow cord or Hose to  
be crimped by closing it in doors. DO NOT pull or stretch cord or Hose around  
sharp corners or edges.  
7. Before filling unit with water, always unplug power cord from electrical outlet.  
Failure to do so may result in electrical shock and injury.  
8. Do not allow electrical cord to touch hot surfaces. Let appliance cool completely  
before putting away. Loop cord loosely around appliance when storing.  
9. DO NOT use this unit with extension cords or electrical outlets that have  
inadequate current capacity. A three-prong outlet or a properly grounded adapter  
is necessary when using SF-475 Fabric Steamer.  
SAVE THESE INSTRUCTIONS!  
FOR HOUSEHOLD USE ONLY  
3
Top Innovations, Inc.  
 
IMPORTANT SAFEGUARDS  
WARNING: To reduce the risk of electrical shock, this appliance  
has a three-pronged plug. This plug will fit in a polarized wall  
outlet only one way. If the plug does not fit fully in the outlet,  
contact a licensed electrician to install a proper outlet. DO NOT  
attempt to modify the plug or defeat this safety feature.  
10. In order to unplug SF-475 Fabric Steamer, grasp plug and pull smoothly and  
firmly from outlet. DO NOT attempt to unplug unit by pulling or tugging on  
cord.  
11. Always keep Steam Nozzle elevated above Water Reservoir. DO NOT lay Hose  
on floor.  
12. Use caution, as burns could occur from touching hot metal parts, hot water or  
steam.  
13. SF-475 Fabric Steamer is only meant to be used with recommended SF-475  
accessories. Other types of attachments are not to be used with Fabric Steamer.  
Doing so may cause injuries or damage to unit.  
14. Nozzle and attachments become hot during use. To avoid injuries, DO NOT  
touch nozzle while using this appliance. DO NOT attempt to change  
attachments while unit is emitting steam.  
15. When filling your Fabric Steamer, only water should be used in unit. Other  
cleaning agents will damage unit and can cause injuries.  
16. DO NOT operate unit if steam opening is blocked. Should this occur,  
immediately cease usage and unplug from electrical outlet.  
17. Store your SF-475 Fabric Steamer in a cool, dry place.  
SAVE THESE INSTRUCTIONS!  
FOR HOUSEHOLD USE ONLY  
4
Top Innovations, Inc.  
 
FABRIC STEAMER PRODUCT INFORMATION  
The following features and accessories are included with your Steam Cleaner. Carefully  
inspect packaging material as some parts are shipped inside Styrofoam packaging. To obtain  
possible missing parts, refer to the Customer Support section on page 13 of this manual.  
UNIT FEATURES  
& ACCESSORIES  
1. Pole Top  
1a. Steam Nozzle Holder  
1b. Clothes Hanger Hook  
2. Steam Nozzle  
3. Handle  
4. Telescopic Pole  
4a. Pole Base  
5. Hose  
5a. Hose Base  
6. Steam Ready Light  
7. Lighted On/Off Switch  
8. Water Reservoir  
9. Storage Compartment  
9a. Water Reservoir Cap  
9b. Compartment Lid  
10. Lint Remover  
11. Fabric Brush  
12. Cloth Cover  
13. Measuring Cup  
14. Water Funnel  
15. Press Pad  
5
Top Innovations, Inc.  
 
FABRIC STEAMER PRODUCT INFORMATION  
The Pole Top (1) is comprised of the Steam Nozzle Holder (1a) and the Clothes  
Hanger Hook (1b). The Steam Nozzle Holder provides a safe and convenient place  
to hang the Steam Nozzle. The Clothes Hanger Hook allows you to steam  
garments that are hanging from a clean, rust-free hanger.  
The Steam Nozzle (2) is designed to spread hot, penetrating steam over a wide  
area.  
The Handle (3) is designed to stay relatively cool while providing the optimum  
amount of safety and user comfort.  
The Telescopic Pole (4) connects the Pole Top to the steamer and collapses to  
allow quick, compact storage of the unit. The Pole Base (4a) is the mount where  
the Telescopic Pole connects to the main unit body.  
The Hose (5) safely channels steam from the boiler to the Steam Nozzle. The Hose  
Base (5a) is the mount where the Hose connects to the main unit body.  
The Steam Ready Light (6) indicates when the unit is ready to steam, by lighting  
up during heating and turning off when the steam is ready.  
The Lighted On/Off Switch (7) turns the unit on and off, and provides a clear  
visual indication when the steamer is turned on.  
The Water Reservoir (8) is where water is stored for use by the unit. There must  
be a sufficient amount of water (16-48 oz.) in the Water Reservoir in order for the  
unit to properly function.  
The Storage Compartment (9) provides a convenient place to store small  
accessories. The Water Reservoir Cap (9a) is located inside the Storage  
Compartment, and must be removed in order to expose the fill hole and fill the  
Water Reservoir with water. The Compartment Lid (9b) is a hinged lid that covers  
the Storage Compartment and Water Reservoir Cap.  
The Lint Remover (10) connects to the Steam Nozzle and is designed to assist in  
removing lint, loose threads and other small particles from fabric.  
The Fabric Brush (11) connects to the Steam Nozzle and is designed to assist in  
smoothing out exceptionally stubborn wrinkles.  
The Cloth Cover (12) is connects to the Steam Nozzle, and is useful for preventing  
large water droplets from dripping on delicate materials.  
The Measuring Cup (13) and Water Funnel (14) are provided to assist you in  
easily and consistently filling the Water Reservoir with the optimum amount of  
water (16-48 oz. / 473-1420 ml.).  
The Press Pad (15) fits on your hand, allowing you to support the fabric for a  
more thorough steaming. The Press Pad also protects your hand from being  
burned by hot steam.  
6
Top Innovations, Inc.  
 
ASSEMBLING THE FABRIC STEAMER  
ATTACHING THE TELESCOPIC POLE  
1. Attach Pole Top by sliding it onto top of Telescopic Pole as shown (FIGURE 1).  
Note that Pole Top must align correctly in two grooves that run the length of pole.  
2. Line up grooves of Telescopic Pole with two tabs inside Pole Base hole, and  
insert bottom section of Pole into Base (FIGURE 2).  
3. Tighten knob by turning it in a clockwise direction until it is tight, and Telescopic  
Pole sits firmly in place in the Pole Base (FIGURE 3).  
FIGURE 2  
FIGURE 1  
FIGURE 3  
EXTENDING TELESCOPIC POLE  
1. Locate bottom extension lock, and swing  
hinge outward as shown (FIGURE 4).  
Extend middle section of Telescopic Pole as  
far upward as it will go, then close hinge to  
relock bottom extension lock.  
2. Repeat Step 1 for remaining two extension  
locks, until Telescopic Pole is extended to  
it’s full height.  
NOTE: It is recommended to extend  
Telescopic Pole to it’s full height during  
steamer operation. This ensures full  
extension of Steam Hose for maximum flow  
of steam.  
FIGURE 4  
7
Top Innovations, Inc.  
 
ASSEMBLING THE FABRIC STEAMER  
CONNECTING HOSE  
1. Slide Hose fitting onto threaded Hose Base (FIGURE 5)  
2. Turn Hose fitting clockwise to secure it to Hose Base (FIGURE 6).  
NOTE: Hand-tighten Hose fitting only. Do not over-tighten.  
3. Hang Steam Nozzle on specially designed Steam Nozzle Holder as shown  
(FIGURE 7).  
CAUTION: To prevent steam from causing bodily injury or damage to  
surfaces, always hang Steam Nozzle on Steam Nozzle Holder when not in use.  
Do not lay Hose on floor as condensation may build up inside, causing  
unwanted water droplets in steam.  
CAUTION: Pulling on Hose with excessive force may damage it, resulting in a  
steam leak.  
FIGURE 6  
FIGURE 5  
FIGURE 7  
ATTACHING LINT REMOVER /  
FABRIC BRUSH / CLOTH COVER  
1. Make sure Lighted On/Off Switch is set to “Off”  
position, and that unit is not emitting any steam.  
Do not try to connect Lint Remover, Fabric  
Brush or Cloth Cover while unit is emitting  
steam, as this can cause burns and injury.  
2. Align two pegs on back of accessory with  
corresponding holes on face of Steam Nozzle.  
Use care to properly align attachment as shown  
(FIGURE 8), so as not to cover up steam holes  
on nozzle face.  
FIGURE 8  
3. Press accessory firmly onto Steam Nozzle, until  
it fits securely in place.  
8
Top Innovations, Inc.  
 
USING THE FABRIC STEAMER  
FILLING WATER RESERVOIR WITH WATER  
1. Place Fabric Steamer on a flat, level surface.  
2. Make sure Lighted On/Off Switch is set to “Off” position and grounded power  
cord is unplugged from electrical outlet.  
3. Flip up Compartment Lid. Cautiously unscrew and remove Water Reservoir Cap.  
4. Water Reservoir should always be emptied after each use. If it was not emptied  
after the last use, empty it now. This will prevent over-filling.  
5. Fill Measuring Cup to maximum fill line (16 oz. / 473 ml.) with water.  
NOTE: To prolong the life of your Fabric Steamer, we recommend using  
distilled or de-mineralized water.  
6. Using Water Funnel, carefully pour water from Measuring Cup into Water  
Reservoir through fill hole.  
WARNING: Extreme caution should be used when pouring water into the  
Water Reservoir. Do not look directly down into fill hole when filling. Keep  
your free hand and any children or pets at a safe distance.  
7. Depending on how long you intend to steam, you may repeat steps 5 & 6 up to  
two more times, to a maximum of 48 oz. (1420 ml.) of water. See chart below  
for a comparison of the amount of water vs. approximate steam time.  
8. Replace Water Reservoir cap, ensuring that it is screwed on tightly to prevent hot  
steam from escaping and causing injury.  
9. Lower Compartment Lid back down.  
IMPORTANT: When steamer is first activated, it is natural for it to spray  
small amounts of water. This is due to condensation forming in the Hose, and  
will dissipate within 30 seconds of use. To help clear condensation out of Hose  
more quickly, try the following:  
• Point Steam Nozzle towards ground, sink or tub and shake it to force water  
out of Hose.  
• Extend Hose vertically as far as possible to allow water to drain back into  
Water Reservoir.  
9
Top Innovations, Inc.  
 
USING THE FABRIC STEAMER  
OPERATING THE FABRIC STEAMER  
NOTE: Be sure that any desired attachments are  
connected and Water Reservoir is filled before following  
these steps.  
1. Plug grounded power cord into a convenient 3-prong  
electrical outlet.  
2. Switch Lighted On/Off Switch to “On” position.  
3. Steam Ready Light will illuminate while boiler is  
heating. When Steam Ready Light deactivates (2-8  
minutes, depending on amount of water in Water  
Reservoir) unit will automatically begin emitting steam.  
4. Place garment on a clean, rust-free clothes hanger.  
5. Place hanger (with garment) on Clothes Hanger Hook  
(FIGURE 10).  
FIGURE 10  
CAUTION: Use care when handling garments on the  
Clothes Hanger Hook. Pulling on the garment with  
too much force may cause the unit to tip over.  
6. Direct Steam Nozzle towards bottom of garment. Steam  
will rise along inside and outside of fabric, removing  
wrinkles. Slowly slide Steam Nozzle vertically, from  
bottom to top of garment (FIGURE 11).  
NOTE: Do not allow kinks to form in hose at any  
time during use.  
7. Direct Steam Nozzle away from garment and smooth  
fabric with your free hand.  
8. Repeat steps 6 & 7 as necessary until fabric is smooth  
and wrinkle free.  
OTHER STEAMING TIPS  
FIGURE 11  
Curtains and draperies may be steamed while still hanging.  
To remove wrinkles from towels, handkerchiefs and napkins, drape them over a rod or  
towel rack and gently steam them.  
Heavier fabrics may require repeated steaming to effectively remove wrinkles.  
To remove exceptionally stubborn wrinkles steam both sides of fabric.  
For additional assistance in removing tough wrinkles, or to remove lint and other particles,  
attach Fabric Brush or Lint Remover to Steam Nozzle (see Attaching Lint Remover and  
Fabric Brush section on page 8 of this manual).  
Use Press Pad in order to steam difficult spots and edges and to create creases in fabric.  
Slide your hand through the velcro strap on back of Press Pad to secure it to your hand.  
This will protect your hand from the flow of hot steam. Then steam fabric while pressing it  
firmly but gently against the Press Pad.  
9. When you have completed your steaming tasks, immediately switch Lighted On/Off  
Switch to “Off” position and unplug power cord from electrical outlet. Refer to Proper  
Storage section on page 11 of this manual for information on proper cleaning and storage  
of Fabric Steamer.  
10  
Top Innovations, Inc.  
 
CARE & STORAGE GUIDELINES  
PROPER STORAGE  
Preparing your Fabric Steamer for storage is quick and simple. When you have fin-  
ished your steaming tasks, follow the steps listed below.  
1. Unplug grounded power cord from electrical outlet.  
2. Allow unit to cool completely (at least 30 minutes).  
3. Remove all attachments from unit.  
4. Drain any remaining water in Water Reservoir into a sink or tub to prevent  
over-filling during your next use.  
5. Unhook three extension locks on Telescopic Pole, and press down on Pole Top  
to collapse Pole into compact storage position. Re-lock extension locks.  
6. Wrap Hose loosely around Telescopic Pole one time, and hang Steam Nozzle  
from Steam Nozzle Holder.  
7. Store all attachments safely away, preferably inside Storage Compartment or near  
Fabric Steamer.  
8. Store Fabric Steamer in a cool, dry location.  
REMOVING MINERAL BUILD-UP  
A common problem with steam appliances is mineral build-up caused by high  
mineral content in many municipal water supplies. The best way to avoid this is  
to use de-mineralized or distilled water in unit. If you are unable to use de-  
mineralized or distilled water, we recommend you use this procedure monthly to  
help avoid mineral build-up:  
1. Switch Lighted On/Off Switch to “Off” position and unplug grounded power  
cord from electrical outlet. Allow unit to completely cool.  
2. Remove all accessories from unit.  
3. Flip up Compartment Lid and remove Water Reservoir Cap.  
4. Drain water from Water Reservoir into sink or tub.  
5. Using Measuring Cup, make a mixture of 8 oz. (236 ml.) vinegar and 8 oz.  
(236 ml.) water.  
6. Slowly pour water-vinegar solution into Water Reservoir.  
7. Allow to stand for 40 minutes.  
8. Drain water-vinegar solution from Water Reservoir.  
9. Rinse Water Reservoir with fresh water, drain and repeat until vinegar odor  
dissipates.  
10. Replace Water Reservoir Cap and lower Compartment Lid back down.  
11  
Top Innovations, Inc.  
 
TROUBLESHOOTING GUIDE  
SOLUTION  
PROBLEM  
POSSIBLE CAUSE  
Unit fails to steam. Lighted  
On/Off Switch does not  
illuminate.  
Unit is not plugged in.  
Plug into electrical  
outlet.  
Household Circuit Breaker /  
Ground Fault Interrupter has  
tripped or blown a fuse.  
Reset Circuit Breaker /  
Ground Fault Interrupter, or  
replace fuse. If you need  
assistance, contact a licensed  
electrician.  
Water Reservoir is empty.  
Mineral build-up in unit.  
Mineral build-up in unit.  
Refill Water Reservoir using  
procedures on page 9 of this  
manual.  
Unit fails to steam. Lighted  
On/Off Switch does  
illuminate.  
Follow Removing Mineral  
Build-Up procedure on page  
11 of this manual.  
Steam output is intermittent.  
It is normal for unit to  
periodically stop steaming  
for a few seconds. If steam  
stays off for longer periods,  
follow Removing Mineral  
Build-Up procedure on page  
11 of this manual.  
Water condensation in Steam  
Hose.  
Unit is emitting excess water.  
Point Steam Nozzle towards  
sink, tub or ground and  
shake. Continue until excess  
water is released.  
Water Reservoir has been  
over-filled.  
Empty some water out of  
Water Reservoir.  
Unit has not reached  
operating temperature.  
Wait until Steam Ready  
Light deactivates to steam.  
Excessive gurgling in Hose  
and Steam Nozzle / water  
drips from Steam Nozzle.  
Condensation in Steam Hose.  
Some gurgling is a natural  
effect of steaming process.  
For excessive gurgling or  
dripping water, extend Hose  
vertically to allow water to  
drain back into Water  
Reservoir.  
12  
Top Innovations, Inc.  
 
TROUBLESHOOTING & CUSTOMER SUPPORT  
SOLUTION  
PROBLEM  
POSSIBLE CAUSE  
Water spills out from Water  
Reservoir fill hole when  
adding water.  
Water Reservoir is already  
full.  
Do not try to add any more  
water.  
Water Reservoir is too hot to  
be refilled.  
Allow more cooling time  
before refilling.  
Fill Water Reservoir more  
slowly. Be sure to utilize the  
provided Measuring Cup and  
Water Funnel to refill the  
unit.  
Accessories do not stay  
firmly attached to Steam  
Nozzle.  
Accessories are not being  
properly installed.  
Review steps for proper  
installation of accessories on  
page 7 of this manual.  
Check to ensure that  
accessories are installed  
correctly.  
Accessories or Steam Nozzle  
is damaged or otherwise  
incorrect.  
Contact our Customer  
Service Department for  
assistance.  
CUSTOMER SUPPORT  
For problems with your Fabric Steamer, please refer to the troubleshooting solutions located  
on pages 12 & 13 of this manual. Additional inquiries should be directed to our Customer  
Support services through our Web site, www.steamfast.com, on the Service Request Web  
page.  
If you do not have internet access, you may also contact our Customer Support Department  
by telephone, at (800) 711-6617 or (816) 584-9700.  
NOTE: In order for our customer service representatives to help you as quickly and  
efficiently as possible, please have the following information ready before calling:  
• Purchase information (where and when you purchased this product)  
• Product Serial Number  
13  
Top Innovations, Inc.  
 
14  
Top Innovations, Inc.  
 
WARRANTY INFORMATION  
ONE YEAR LIMITED WARRANTY  
(If outside USA, additional shipping charges may apply)  
Top Innovations, Inc. warrants this product to be free from defects in material and  
workmanship for a period of one (1) year from the date of purchase. This warranty  
does not cover damage caused by misuse, negligence, use by improper current or  
voltage, commercial use, use contrary to operating instructions or disassembly, repair or  
alteration by any person other than Top Innovations, Inc. Warranty Service Department.  
Top Innovations, Inc. will repair or replace, at its option. This warranty gives you  
specific legal rights and may have other rights, which may vary from state to state.  
Performance of any obligation under this warranty may be obtained by:  
1. Call (800) 711-6617 for Return Authorization Number before returning for  
repair. Failure to obtain a Return Authorization Number will cause a delay in  
warranty and out-of-warranty service requests.  
2. Include copy of purchase receipt.  
3. Include your name, address, telephone number, and Return Authorization  
Number on returned package.  
Please send product postage-prepaid to:  
TOP INNOVATIONS, INC.  
WARRANTY SERVICE DEPARTMENT  
6655 TROOST AVE.  
KANSAS CITY, MO 64131  
Should there be any missing or defective parts or accessories, please contact Customer  
Support. In most cases, it is not necessary to return the entire unit. We can ship most  
parts directly to your door.  
Upon expiration of 1 year limited warranty, you will be advised of the cost of repair  
before any servicing is done, unless you enclose a note indicating that you would like us  
to proceed with repairs.  
If you need to request warranty service, or have any questions about coverage under this  
warranty, please visit the Warranty Service Request page on our Web site  
www.steamfast.com. You may also contact the Warranty Service Department by  
telephone at (800) 711-6617 or (816) 584-9700, or e-mail  
Please have your product serial number ready before contacting Warranty Service  
Department. The serial number is located on the back or bottom of your unit.  
15  
Top Innovations, Inc.  
 
Top Innovations, Inc.  
6655 Troost Ave.  
Kansas City, MO 64131  
Tel: (800) 711-6617  
(816) 584-9700  
Printed in China  
PRODUCT SERIAL NUMBER  
For your convenience, space has been provided below for  
you to record the serial number of your unit (located on the  
back or bottom of the unit) for easy reference when  
contacting our Customer Service Department.  
________________ - ______________________________  
V051213  
 

Taylor Outdoor Timer 5806 User Manual
Texas Instruments Computer Drive TMS320DM648 User Manual
Toastmaster Cooktop TMCKM2SIM User Manual
Tokina Camera Accessories TC2814DC User Manual
Toshiba Flat Panel Television 20HL67 User Manual
Toshiba VCR RD XV48DTKF User Manual
Tricity Bendix Freezer TB 44 UF User Manual
Tripp Lite Welding System 1250 3000 VA User Manual
Turbo Chef Technologies Oven 30 Single Wall User Manual
Viking Computer Drive PSFEM1xxxGQxxx User Manual