MULTIFUNCTIONAL DIGITAL COLOR SYSTEMS /
MULTIFUNCTIONAL DIGITAL SYSTEMS
High Security Mode
Management Guide
Preface
Thank you for purchasing Toshiba Multifunctional Digital Systems.
This manual explains about the conditions and settings for using the Multifunctional Digital Systems which complies with
IEEE Std 2600.1TM-2009 *1
.
Read this manual carefully before using your Multifunctional Digital Systems under the high security mode. For the
security precautions on operating the equipment complying with IEEE Std 2600.1TM-2009, refer to “Security Precautions”
in the “Safety Information”.
Keep this manual within easy reach and use it to maintain the equipment complying with IEEE Std 2600.1TM-2009.
„ How to read this manual
‰ Symbols in this manual
In this manual, some important items are marked with the symbols shown below. Be sure to read these items before using
this equipment.
Indicates a potentially hazardous situation which, if not avoided, could result in death, serious
injury, or serious damage, or fire in the equipment or surrounding assets.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate
injury, partial damage to the equipment or surrounding assets, or loss of data.
Indicates information to which you should pay attention when operating the equipment.
Other than the above, this manual also marks information that may be useful for the operation of this equipment with the
following signs:
Describes handy information that is useful to know when operating the equipment.
Pages describing items related to what you are currently doing. See these pages as required.
‰ Model and series names in this manual
In this manual, each model name is replaced with the series name as shown below.
Model name
e-STUDIO5540C/6540C/6550C
Series name in this manual
e-STUDIO6550C Series
e-STUDIO2040C/2540C/3040C/3540C/4540C
e-STUDIO4540C Series
e-STUDIO456 Series
e-STUDIO206L/256/306/356/456/506,
e-STUDIO256SE/306SE/356SE/456SE/506SE
e-STUDIO556/656/756/856,
e-STUDIO856 Series
e-STUDIO556SE/656SE/756SE/856SE
e-STUDIO2050C/2550C
e-STUDIO2550C Series
‰ Explanation for control panel and touch panel
y Illustrations for the control panel and the touch panel shown in this manual are those of the e-STUDIO4540C Series.
The shape and location of some buttons on the control panel and the dimension of the touch panel of the
e-STUDIO6550C Series, e-STUDIO456 Series, e-STUDIO856 Series, e-STUDIO2550C Series differ from those of the
e-STUDIO4540C Series, however, the names and functions of the buttons and parts are the same.
y The details on the touch panel menus may differ depending on the operating environment such as whether options are
installed.
y The illustration screens used in this manual are for paper in the A/B format. If you use paper in the LT format, the
display or the order of buttons in the illustrations may differ from that of your equipment.
‰ Options
For the available options, refer to "Options" in the Quick Start Guide for your equipment.
Preface
1
‰ Trademarks
y The official name of Windows XP is Microsoft Windows XP Operating System.
y The official name of Windows Vista is Microsoft Windows Vista Operating System.
y The official name of Windows 7 is Microsoft Windows 7 Operating System.
y The official name of Windows Server 2003 is Microsoft Windows Server 2003 Operating System.
y The official name of Windows Server 2008 is Microsoft Windows Server 2008 Operating System.
y Microsoft, Windows, Windows NT, and the brand names and product names of other Microsoft products are
trademarks of Microsoft Corporation in the US and other countries.
y Apple, AppleTalk, Macintosh, Mac, Mac OS, Safari, and TrueType are trademarks of Apple Inc. in the US and other
countries.
y Adobe, Acrobat, Reader, and PostScript are either registered trademarks or trademarks of Adobe Systems
Incorporated in the United States and/or other countries.
y Mozilla, Firefox and the Firefox logo are trademarks or registered trademarks of Mozilla Foundation in the U.S. and
other countries.
y IBM, AT and AIX are trademarks of International Business Machines Corporation.
y NOVELL, NetWare, and NDS are trademarks of Novell, Inc.
y TopAccess is a trademark of Toshiba Tec Corporation.
y Other company and product names given in this manual or displayed in this software may be the trademarks of their
respective companies.
2
Preface
CONTENTS
Temporary Password............................................................................................................. 10
Conditions when a temporary password is used................................................................. 10
Logging in............................................................................................................................ 14
CONTENTS
3
4
CONTENTS
1.
THE HIGH SECURITY MODE
Precautions on Using the High Security Mode .....................................................................6
Confirmation of the mode.......................................................................................................................................6
1 THE HIGH SECURITY MODE
Precautions on Using the High Security Mode
This operation mode protects customers’ important information against unauthorized access to the equipment and
leakage.
The following are the security functions when you operate the equipment complying with IEEE Std 2600.1TM-2009.
y User Authentication Setting function
y Role Management function
y Encryption function of data to be written in HDD
y Log collecting and browsing function
y Overwriting function of the specified data in HDD when jobs are completed or the power is turned ON
y Communication function with SSL or TLS
y Integrity Check function
y Management functions such as:
Log, Passwords, User, Password Policy, Date & Time, Auto Clear, Session Timer, Enable/disable of SSL/LTS
We have applied for ISO/IEC 15408 certification for the environment where the following equipment is operating in
Japanese or English mode and connected to a PC running Windows XP or Vista with Internet Explorer version 8.0.
e-STUDIO5540C/6540C/6550C
e-STUDIO2040C/2540C/3040C/3540C/4540C
e-STUDIO206L/256/306/356/456/506,
e-STUDIO256SE/306SE/356SE/456SE/506SE
e-STUDIO556/656/756/856,
e-STUDIO556SE/656SE/756SE/856SE
e-STUDIO2050C/2550C*
*
Certification pending (as of July, 2012)
To operate the equipment complying with IEEE Std 2600.1TM-2009 under the high security mode, configurations according
to the use environment, such as data or protocol encryption setting and setting for the connection only to the authorized
server or client PC, are required.
Pay attention that if the conditions given in this manual are not met, you may not be able to operate the equipment
complying with IEEE Std 2600.1TM-2009.
y For details of each security function and how to set the related items, refer to the TopAccess Guide.
y The optional hard disk kit (GE-1220) is required to use e-STUDIO2050C/2550C in high security mode.
„ Confirmation of the mode
When this equipment is operated under the high security mode,
is displayed on the touch panel of the equipment.
6
Precautions on Using the High Security Mode
1 THE HIGH SECURITY MODE
1.THE HIGH SECURITY MODE
y The HDD inside the equipment which is operated under the high security mode is encrypted. Moreover, the Data
Overwrite Option (GP-1070) is installed in such equipment.
To confirm that each function is operating, check the display at the top right of the [Counter] screen on the touch
panel of the equipment.
The HDD is encrypted.
The icon is displayed.
Even in the case that it is not displayed, the HDD has been encrypted if this
equipment has been operated under the high security mode.
The Data Overwrite Enabler is operating
properly.
The icon showing that the Data Overwrite Enabler is correctly operating
is displayed.
The version of the system (V1.0) is displayed.
y When the Data Overwrite Enabler is installed, the hard disk space temporarily used during job process will be used
for another job after the data are overwritten.
„ Operational conditions
Select [MFP Local Authentication] for [Authentication Type] in [User Authentication]. If an SNTP
server, LDAP server or DNS server is used for user authentication, the equipment is no longer
complying with IEEE Std 2600.1TM-2009.
When connecting the equipment from any of eFiling BackUp/Restore Utility, File Downloader, TWAIN
Driver or AddressBook Viewer, enter an ID and password to log in. The password input is displayed in
the blank symbols. In addition, you will be locked out if the password is input incorrectly a certain
number of times.
Manually select [FULL] to perform integrity check.
*
For details of the integrity check, refer to the MFP Management Guide.
Do not change the communication settings of the equipment from the initial values. Communication
via a network can be protected by SSL if no such changes are made.
Set to OFF [MEMORY TX] under [USER FUNCTIONS] - [ADMIN] - [LIST/REPORT] - [REPORT SETTING]
- [COMM. REPORT].
In the High Security Mode, the following functions cannot be used.
y Interrupt copy
y Network Fax
y Scheduled printing
y Storing to e-Filing from a printer driver*
*
The function can be selected; however, an error occurs and the job is deleted. As a result, printing is not performed. When a job is deleted,
it is recorded in the error log. Confirm it in the [Logs] tab on TopAccess or [JOB STATUS] - [LOG] - [PRINT] in the equipment.
y Disabling log authentication
Precautions on Using the High Security Mode
7
1 THE HIGH SECURITY MODE
The automatic log-in function in the client software which comes with this equipment is not available.
Be sure to enter the user name and password when using client software.
Any data sent to this equipment, such as a Fax and Internet Fax printed or received from a printer
driver*, can be outputted only when a user with the printing privilege is logged in.
*
Use IPP SSL or SSL of WS Print for the communication with the equipment.
number]/Print” into the URL field.
(e.g.: https://192.168.1.2:443/Print)
*
For details, refer to [IPP printing] under [Installing the Printer Drivers] - [Other Installations] in the Software installation guide.
Do not use any applications which need a setting change of the [ODCA] sub menu in the [Setup] menu
on the [Administration] tab under TopAccess.
To securely operate this equipment, we recommend you to observe the following items.
y Use the encrypted PDF format when saving or sending a file and the encryption level shall be 128 bit AES.
y Specify a reliable remote PC for the saving destination of the scan data.
y Do not use PUBLIC BOX in e-Filing since no password can be set.
y Do not use MFP LOCAL since no password can be set.
y When printing a Report by InternetFax, do not select “Print 1st page image” so that no copy of the original will be
added.
y Use SMP Submission in [Print Share].
y Disable [Enable Raw TCP] and [Enable LPD] in Print Service.
y Administrators must regularly export and store the logs.
y Select [Disable] in [Twain Scanning].
8
Precautions on Using the High Security Mode
2 UNIQUE FUNCTIONS
Temporary Password
In the high security mode, a password, tentatively assigned by an administrator to allow a user access, is treated as a
temporary one. To use the equipment, you need to register your password after accessing it with the temporary one.
The security level is insufficient if you continue to use the temporary password. Register your password as soon as
possible.
„ Conditions when a temporary password is used
A user temporary password is used in the following cases:
y For the first time to log in to the equipment after being registered by an administrator.
y When an administrator resets the user’s password.
y When the user information password imported by an administrator is plain text.
When an administrator resets users' passwords, they must be so notified and prompted to change them to ones of
their own choosing.
To prevent user information exported from an equipment from being altered, it is hashed. If you change the password
for the exported user information, plain text is used for the password.
„ Operation by a user when a temporary password is used
If your password can be registered when accessing.
y Registering your password on the control panel
Enter the user name and a temporary password in the User Authentication menu. When you press [OK] in the
confirmation screen for the temporary password, the password entry screen appears. Enter the temporary password in
[OLD PASSWORD]. Enter your new password in [NEW PASSWORD] and [RETYPE NEW PASSWORD], and then
press [OK]. The new password is registered and you can log in to the equipment.
y Registering your password in TopAccess
When you access the equipment from TopAccess, the log-in screen appears. Enter the user name and a temporary
password in the log-in screen, and then press [Login]. When the registration screen appears, enter your new password
in [NEW PASSWORD] and [RETYPE NEW PASSWORD], and then press [SAVE]. The new password is registered
and you can log in to TopAccess.
If you cannot register a new password when accessing the equipment.
In the following utilities, an error occurs when you try to log in to the equipment with a temporary password. Therefore a
new password cannot be registered either. Before using these utilities, register a new password on the control panel or in
TopAccess.
y Remote Scan driver
y e-Filing Web Utility
y Back Up/Restore Utility
y File Downloader
y TWAIN Driver
y AddressBook Viewer
10 Temporary Password
2 UNIQUE FUNCTIONS
HOLD (FAX)
In the high security mode, when an email to which a FAX, Internet FAX or image is received, it is not automatically output.
These jobs are stored in the [HOLD (FAX)] queue and only a user having the [Fax Received Print] privilege can print the
job.
If a job is in the [HOLD (FAX)] queue, the MEMORY RX / LINE lamps blink.
Printing a job in the HOLD (FAX) queue
Log in to the equipment as a user having the [Fax Received Print] privilege.
1
Press the [PRINT] button on the control panel.
2
Select [HOLD (FAX)].
3
y All jobs in the [HOLD (FAX)] queue are displayed.
HOLD (FAX) 11
2 UNIQUE FUNCTIONS
Select the desired job or [SELECT ALL], and then press [PRINT].
4
y The job that has been output is deleted from the [HOLD (FAX)] queue.
12 HOLD (FAX)
3.
THE INITIAL VALUES
Logging in.............................................................................................................................................................14
Initial value list......................................................................................................................................................15
3 THE INITIAL VALUES
Precautions on the Initial Values
To securely operate the equipment, the initial and selectable values in the equipment under the high security mode may
differ from those under the normal security mode. This manual only explains about the initial values and setting items
which are different from those under the normal security mode.
To operate the equipment complying with IEEE Std 2600.1TM-2009, do not change the initial settings described in this
manual.
y For the initial and setting values in the normal security mode, refer to the TopAccess Guide and MFP Management
Guide.
y To reset all settings by performing “Initialization” of this equipment, back up the setting of this equipment and
customers’ data before initializing. For details, refer to the TopAccess Guide and MFP Management Guide.
„ Logging in
y The [User Management] and [Administration] tabs in TopAccess are displayed by logging in as a user with the
administrator privilege. Open TopAccess, click “Login” on the top right, and then enter the user name and password to
log in.
y Be sure to log in the [ADMIN] tab in the [USER FUNCTIONS] mode of the equipment as a user with the Administrator
privilege.
14 Precautions on the Initial Values
3 THE INITIAL VALUES
3.THE INITIAL VALUES
„ Initial value list
[Administration] Tab
[Setup] Menu
[General] Sub Menu
Functions
Save as FTP
Disable
Disable
Disable
Disable
Enable
Network iFax
Network Fax
Web Services Scan
Twain Scanning
The initial value is the same as that of in the Normal
Security Mode; however, be sure to set to OFF.
Restriction on Address Book Operation by Administrator
Can be operated by Administrator only
Energy Save
Auto Clear *
45 Seconds
The initial value is the same as in the Normal Security
Mode; however, OFF cannot be selected.
*
The value can be changed in the [ADMIN] tab in the [User Function] mode in the touch panel of the equipment.
[Network] Sub Menu
HTTP Network Service
Enable SSL*
Enable
SMTP Client
Enable SSL
Verify with imported CA
certification(s)
The secure setting is "Verify with imported CA
certification(s)" or "Accept all certificates without CA".
Authentication
AUTO
Be sure to confirm that one of "CRAM-MD5", "Digest-
MD5", "Kerberos" or "NTLM (IWA)" is applied to your use
environment.
SMTP Server
Enable SMTP Server
POP3 Network Service
Enable SSL
Disable
Verify with imported CA
certification(s)
FTP Client
Enable SSL
Verify with imported CA
certification(s)
FTP Server
Enable SSL
Enable
SNMP Network Service
Enable SNMP V1/V2
Enable SNMP V3
Web Services Setting
Enable SSL
Disable
Enable
Enable
Disable
Web Services Scan
*
The value can be changed in the [ADMIN] tab in the [User Function] mode in the touch panel of the equipment.
[Printer] Sub Menu
General Setting
Restriction for Print Job
Only Hold
[Print Service] Sub Menu
IPP Print
Enable SSL
FTP Print
Enable
Disable
Enable FTP Printing
Precautions on the Initial Values 15
3 THE INITIAL VALUES
[ODCA] Sub Menu
Network
Enable Port
Disable
[Security] Menu
[Authentication] Sub Menu
User Authentication Setting
User Authentication
Authentication Type
Enable Guest User
Enable
You cannot change the setting to "Disable".
MFP Local Authentication
No check mark (Disable)
The initial value is the same as in the Normal Security
Mode; however, it cannot be set to "Enable".
[Password Policy] Sub Menu
Policy for Users
Minimum Password Length 8 (digits)
Requirements to Apply
Lockout Setting
Enable
Enable
(Same as in the Normal Security Mode)
(Same as in the Normal Security Mode)
Number of Retry
3 (times)
2 (minutes)
Disable
Lockout Time
Available Period
Expiration day(s)
90 (days)
Policy for Administrator, Auditor
Minimum Password Length 8 (digits)
Requirements to Apply
Lockout Setting
Number of Retry
Lockout Time
Enable
Enable
(Same as in the Normal Security Mode)
(Same as in the Normal Security Mode)
3 (times)
2 (minutes)
Disable
Available Period
Expiration day(s)
90 (days)
Policy for e-Filing Boxes, Template Groups, Templates, SecurePDF, SNMPv3, Cloning, Secure Receive
Minimum Password Length 8 (digits)
Requirements to Apply
Lockout Setting
Number of Retry
Lockout Time
Enable
Enable
(Same as in the Normal Security Mode)
3 (times)
2 (minutes)
16 Precautions on the Initial Values
FC-5540C/6540C/6550C
FC-2040C/2540C/3040C/3540C/4540C
DP-2095/2530/3020/3590/4590/5010
DP-5560/6560/7560/8560
FC-2050C/2550C
OME100078F0
MULTIFUNCTIONAL DIGITAL COLOR SYSTEMS /
MULTIFUNCTIONAL DIGITAL SYSTEMS
High Security Mode Management Guide
2-17-2, HIGASHIGOTANDA, SHINAGAWA-KU, TOKYO, 141-8664, JAPAN
©2012 TOSHIBA TEC CORPORATION All rights reserved
R100520J1406-TTEC
Ver06 2012-06
|